#WINDOWS PHONE 7 CONNECTOR SOFTWARE WINDOWS 10#
#WINDOWS PHONE 7 CONNECTOR SOFTWARE PC#
#WINDOWS PHONE 7 CONNECTOR SOFTWARE WINDOWS#

When the traffic drops below this threshold, the interface will be disconnected. This allows ongoing active use of the interface, such as from a file transfer or VoIP call, to avoid disruption. If the traffic level is above a certain threshold, no further action is taken.

#WINDOWS PHONE 7 CONNECTOR SOFTWARE WINDOWS#

Windows then checks the traffic level on the interface every 30 seconds. Networking applications should listen for these events and proactively move their connections to the new network, if possible. This notification to the TCP stack generates a network status change. The existing TCP sessions will continue uninterrupted, but new TCP sessions will use this interface only if explicitly bound or if no other interface routes to the desired destination. Abrupt disconnections degrade the user experience without providing an appreciable benefit and are avoided when possible.ДЄs soon as Windows decides to soft-disconnect an interface, it informs the TCP stack that the network should no longer be used. When Windows decides that a network should no longer be connected, it does not immediately disconnect. The soft disconnect policy works as follows: A WLAN can only be connected (automatically or manually) when there is no Ethernet connection. However, if there is an Ethernet connection, Windows does not permit users to connect to a WLAN manually. If this policy setting is set to 3, the behavior is similar to when it is set to 2. This option was first available in Windows 10, version 1703. When the user is connected to a WLAN or Ethernet connection, no Internet traffic is routed over the cellular connection. However, if a cellular data connection is available, that connection will always stay connected for services that require a cellular connection. If this policy setting is set to 2, the behavior is similar to when it is set to 1. This option was first available in Windows 8. This was previously the Enabled state for this policy setting in builds of Windows before Windows 10, version 1809, build 17763.404. Users can still manually connect to any network. The order of preference is as follows:Д®thernet is always preferred when connected. If this policy is set to 1, any new automatic Internet connection is blocked when the computer has at least one active Internet connection to a preferred type of network. This was previously the Disabled state for this policy setting in builds of Windows before Windows 10, version 1809, build 17663.404. Internet traffic can be routed over any connection, including a cellular connection or any metered network. If this policy is set to 0, a computer can have simultaneous connections to the Internet, to a Windows domain, or to both. If multiple connections are allowed, the policy then determines how network traffic is routed. This policy setting determines if a computer can have multiple connections to the Internet, to a Windows domain, or to both. In Windows 10, version 1809, build 17763.404 and later, this value is an enumeration that is only available through Group Policy.

Windows will not connect to a new network from which it would immediately soft-disconnect.

This is also used to evaluate available networks that are not connected.

#WINDOWS PHONE 7 CONNECTOR SOFTWARE PC#

The most preferred connection to the Active Directory domain, if the PC is joined to a domainДЄll remaining networks are soft-disconnected, as described in the next section. The most preferred connection to the Internet Windows maintains connectivity to the following networks:ДЄny networks that were manually connected during the current user session If this policy is enabled, Windows attempts to maintain the smallest number of concurrent connections that offer the best available level of connectivity. If this policy is disabled, the behavior is similar to that for WindowsВ 7 in which each interface connects to the most preferred network in range, regardless of the connectivity state of other interfaces.

#WINDOWS PHONE 7 CONNECTOR SOFTWARE WINDOWS 10#

In Windows 8, Windows 8.1, and versions of Windows 10 before Windows 10, version 1809, build 17763.404, this policy is a boolean value that can be modified using either Group Policy or the WcmSetProperty API. Versions of Windows before Windows 10, version 1809, build 17763.404

It is on by default for WindowsВ 8, WindowsВ 8.1, and WindowsВ 10. This policy is configured using the fMinimizeConnections Group Policy. These policies are not exposed in the Windows user interface but can be configured by using the WcmSetProperty API or Group Policy. WindowsВ 8, WindowsВ 8.1, and WindowsВ 10 include a number of policies to control connection management. Pure virtual interfaces, such as VPNs and tunneled IP connections This topic describes how Windows automatically manages physical wireless connectivity and does not consider these connections: Windows responds to Ethernet connections but does not automatically manage Ethernet connections.

Windows phone 7 connector software